View TEA19363T_9040746.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge rev. 1 20 october 2016 product data sheet 1 general description the TEA19363T is a member of the greenchip family of controller ics for switched mode power supplies. it is intended for flyback topologies to be used either standalone or together with usb pd or smart charging controllers (like the tea190x series) at the secondary side. the built-in green functions provide high efficiency at all power levels. the TEA19363T is compatible with multiple output voltage applications with a wide output range from 5 v to 20 v in constant voltage (cv) mode. when used with a secondary-side controller ic, like the tea190x series, it supports constant current (cc) mode down to 3 v output voltage. to support computing applications that typically have an x-capacitor with a higher value than 100 nf, the TEA19363T incorporates an active x-capacitor discharge function. at high power levels, the flyback converter operates in quasi-resonant (qr) mode. at lower power levels, the controller switches to frequency reduction (fr) in discontinuous conduction mode (dcm) operation. the peak current is limited to a minimum level. valley switching is used in all operating modes. at very low power levels, the controller uses burst mode to regulate the output power. a special optocoupler current reduction regulation has been integrated which reduces the average optocoupler current in all modes to a minimum level. this reduction ensures high efficiency at low power and excellent no-load power performance. as the switching frequency in this mode is never less than f sw(min) and the burst repetition rate is regulated to a low value, the audible noise is minimized. during the non-switching phase of the burst mode, the internal ic supply current is minimized for further efficiency optimization. the TEA19363T includes a wide set of protections that are safe restart protections. if the output is shorted, the system stops switching and restarts. the output power is then limited to a lower level. if the output is shorted, the system stops switching and restarts. the output power is then limited to a lower level. the TEA19363T is manufactured in a high-voltage silicon-on-insulator (soi) process. the soi process combines the advantages of a low-voltage process (accuracy, high- speed protection, functions, and control). however, it also maintains the high-voltage capabilities (high-voltage start-up, low standby power, and brownin/brownout sensing at the input). the TEA19363T enables low-cost, highly efficient and reliable supplies for power requirements up to 75 w using a minimum number of external components.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 2 / 34 2 features and benefits 2.1 general features ? smps controller ic supporting smart-charging applications and multiple-output-voltage applications ? wide output range (5 v to 20 v in cv mode, 3 v to 20 v in cc mode, and 3 v to 6 v in direct charging mode) ? housed in a small so10 package ? adaptive dual supply for highest efficiency over the entire output voltage range ? integrated high-voltage start-up and x-capacitor discharge ? continuous v cc regulation during start-up and protection via the hv pin, allowing a minimum vcc capacitor value ? reduced optocurrent enabling low no-load power (20 mw at 5 v output) ? fast transient response from 0 to full load ? minimal audible noise and output voltage ripple in all operating modes ? integrated soft start 2.2 green features enables high efficiency operation over a wide power range via: ? low supply current during normal operation (0.6 ma without load) ? low supply current during non-switching state in burst mode (0.2 ma) ? valley switching for minimum switching losses ? frequency reduction with fixed minimum peak current to maintain high efficiency at low output power levels 2.3 protection features all protections are safe restart protections. ? mains voltage compensated overpower protection (opp) ? overtemperature protection (otp) ? integrated overpower timeout ? integrated restart timer for system fault conditions ? continuous mode protection using demagnetization detection ? accurate overvoltage protection (ovp) ? general-purpose input for safe restart protection; for use with system overtemperature protection (otp) ? driver maximum on-time protection ? brownin and brownout protection 3 applications ? applications requiring efficient and cost-effective power supply solutions up to 75 w without touchscreen
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 3 / 34 4 ordering information table 1. ordering information type number package name description version TEA19363T /1 so10 plastic small outline package; 10 leads; body width 3.9 mm; body thickness 1.35 mm sot1437-1 5 marking table 2. marking codes type number marking code TEA19363T/1 TEA19363T
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 4 / 34 6 block diagram a ton > 55 s v = f ( l a u x ) b l a n k l p e a k l p e a k s o f t s t a r t s o f t s t a r t g a t e o c p d r i v e r i s e n s e v i n m e a s u r e val l e y ise n s e aux i a u x s t a r t o p c n t r a/d conve rsion v c c c h a r g e d v i a h v c u r r e n t s o u r c e i p r o t e c t = o n v c t r l = o n n o r m a l m o d e ivcc = 6 0 0 a oscilla t o r and timin g s i g n a l s dela y tim ers offs e t a/d a/d s a f e - r e s t a r t p r o t e c t i o n m o d e v c c r e g u l a t e d t o v c c s t a r t ivcc = 2 2 0 a e n a b l e 4 0 m s 2 0 0 m s o p c o u n t e r v o u t r e g u l a t e d o p d e t e c t i o n t o n m a x s t a n d b y m o d e ivcc = 2 3 5 a t e m p e r a t u r e p r o t e c t i o n p e r i o d c o u n t e r n n e w = f ( n p r e v , t p e r i o d ) r e g i s t e r o n t i m e c o u n t e r t o n _ c o u n t t o n _ r e f t p e r i o d iso ftsta rt = o n hvj fet h v vcc h digital contro l brownout tonmax gate gate v i n m e a s u r e sta r t o p c n t r 8 0 0 m s e n a b l e s a f e r e s t a r t c o u n t e r restart r s s e t rst a b a b q d c l k g a t e r q s q gate otp aaa-0238 9 7 v c c sta r t sta ndby m o d e normal mode burston dem a g v a l l e y brownout protecti o n ocp sta r t o p c n t r auxovp / 4 c p pul s e 1 m s pow e r - d o w n ovp+ protect 14.8 v 1.45 v 1 1 v 9.9 v 8.65 v 1.2 5 ma 13 v 47 a 74 a 0.5 v 3.5 v 5 v 0.2 v 3 v aux 200 na 5 v dem a g v a l l e y dete c t 35 m v v c c low v c c sto p v c c reset v c c charge v c c > v c c s t a r t v c c > v c c r e s e t t = 8 0 0 m s a n d v c c > v c c r e s e t vcc>vccs top ise n s e > 0 . 7 6 5 v p r o t e c t i o n v c t r l > 0 . 5 v v c c d i s c h a r g e nr of ga t e pul s e s > 4 0 v p r o t e c t > 0 . 5 v v c t r l > 5 v v c c di s c h a r g e v ccl protect 80 a 100 a + 1 a h y s gnd ctrl b u r s t o n b u r s t m o d e l o p t o l t 1 0 0 u l o p t o l t 1 0 0 u 1 3 0 k h z l o p t o l t 1 0 0 u v o u t r e g u l a t e d v c c s t o p c t r l _ p 7 5 0 m v 1 4 0 m v 2 5 k h z 2 . 2 5 v 4 . 1 v 1 . 8 v c t r l _ p fre q f r e q u e n c y v l p e a k 6 k figure 1. TEA19363T block diagram
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 5 / 34 7 pinning information 7.1 pinning aaa-020153 i c 1 2 3 4 5 1 0 9 8 7 6 h v n.c. protect ctrl aux vcch gnd vccl isense driver figure 2. TEA19363T pin configuration (so10) 7.2 pin description table 3. pin description symbol pin description vcch 1 higher supply voltage gnd 2 ground vccl 3 lower supply voltage isense 4 current sense input driver 5 gate driver output aux 6 auxiliary winding input for demagnetization timing, valley detection, overpower correction, and ovp ctrl 7 control input protect 8 general-purpose protection input; pin for power-down mode n.c. 9 high-voltage safety spacer; not connected hv 10 high-voltage start-up; active x-capacitor discharge
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 6 / 34 8 functional description 8.1 supply management the chip is supplied by high-voltage mains via the hv pin during start-up and protection mode. when the system starts switching, the auxiliary windings take over the supply. the ic has two supply pins, the vcch and vccl pins. the lower pin (vccl) supplies the ic directly. the higher supply pin (vcch) is connected to the vccl pin via an internal voltage regulator. when used in an application, which supports multiple output voltages, a pair of auxiliary transformer windings can be used to supply the ic efficiently at all output levels. to supply the ic at higher output voltages, the winding with fewer turns can be connected to the vccl pin. at the lower output voltages, the winding with more turns can supply the ic via the vcch pin. the voltage capability of these pins is chosen such that applications with an output voltage range from 3 v to 20 v are supported optimally. when the voltage on the vccl pin drops to below v integd(vccl) , the regulator between the vcch and vccl pins turns on. all internal reference voltages are derived from a temperature compensated on- chip band gap circuit. internal reference currents are derived from a trimmed and temperature-compensated current reference circuit. 8.2 start-up and undervoltage lockout (uvlo) initially, the capacitor on the vccl pin is charged from the high-voltage mains using the hv pin. the voltage on the vcch pin follows (via an internal diode) the voltage on vccl pin. in this way, the capacitor on the vcch pin is charged. as long as v cc (the voltage on pin vccl) is below v startup , the ic current consumption is minimized. when v cc reaches the v startup level, the control logic activates the internal circuitry. the ic waits for the protect pin to reach v det(protect) + v det(hys)protect and the mains voltage to increase to above the brownin level. meanwhile, the internal power-control signal (which depends on the current at the ctrl pin) also increases to its maximum value. when all these conditions are met, the system starts switching with soft start. in a typical application, the auxiliary winding of the transformer takes over the supply. during the start-up period, the vcc pin is continuously regulated to the v startup level using the hv charge current. the pin is regulated until the output voltage is at its regulation level, which is detected via the ctrl pin. in this way, the vcc capacitor value can be limited. due to the limited current capability from the hv pin mains voltage dependent, the voltage on pin vcc can still drop slightly during the start-up period.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 7 / 34 aaa-020155 3 2 1 4 p r o t e c t o k i n p u t v o l t a g e o k b r o w n i n d e t e c t i o n a c t i v e r e c t i f i e d m a i n s g a t e v cc(stop) v cc(start) v c c figure 3. start-up sequence 8.3 modes of operation the TEA19363T operates primarily in fixed frequency dcm mode. at low powers, it enters burst mode. at high powers, it can operate in quasi-resonance (qr) mode (see figure 4 ). the auxiliary winding of the flyback transformer provides demagnetization information. aaa-023870 d drain voltage at different points c b a 25 khz v opp(isense) 140 mv l peak 130 khz f d c b a quasi-resonant mode discontinuous mode with valley switching frequency reduction system enters burst mode from here p p figure 4. modes of operation
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 8 / 34 at high output power, the converter operates in qr-mode. each converter cycle starts after the demagnetization of the transformer and the detection of the valley at the end of the previous cycle. in qr-mode, switching losses are minimized because the external mosfet is switched on while the drain-source voltage is minimal. to limit the frequency of operation and enable good efficiency, the qr operation switches to dcm operation with valley skipping when the maximum frequency limit (f sw(max) ) is reached. this frequency limit reduces the mosfet switch-on losses and conducted electromagnetic interference (emi). at medium power levels, the controller enters frequency reduction (fr) mode. a voltage controlled oscillator (vco) controls the frequency. the minimum frequency in this mode is (f sw(min) ). to maintain high efficiency, the primary peak current is kept at a minimum level during fr-mode. valley switching is also active in this mode. at low power, the converter enters the burst mode. in burst mode, the switching frequency is f sw(min) . 8.4 mains voltage measuring in a typical application, the mains input voltage is measured using the hv pin. the mains voltage is measured every 1 ms by pulling down the hv pin to ground and measuring its current. this current then reflects the input voltage. the system determines if the mains voltage is connected and its value exceeds the brownin level using an analog-to-digital converter and digital control(see figure 1 ). when the mains exceeds the brownin level, the system is allowed to start switching (see figure 5 ). if the mains voltage is continuously below the brownout level for at least 30 ms after start-up, a brownout is detected and the system immediately stops switching. this period is required to avoid that the system stops switching due to the zero crossings of the mains or during a short mains interruption. aaa-020157 rectified mains voltage driver < 3 0 m s 3 0 m s v brownin v brownout figure 5. mains voltage measuring when the mains voltage is measured by pulling the hv pin to ground, the digital control calculates if there is a positive dv/dt at the mains. a positive dv/dt implies that a mains is connected. when a mains is detected, the measuring of the mains input voltage is stopped for 6 ms to improve efficiency. in burst mode, this waiting period is increased to 97 ms. when succeeding samples cross the brownin level (i bi(hv) ) or the mains high level (i ih(hv) ; see figure 6 ), a positive dv/dt is measured.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 9 / 34 aaa-020158 2 8 m s 6 m s p o s i t i v e d v / d t d e t e c t e d syst e m w i l l s t o p s e n s i n g f o r 6 m s 6 m s 6 m s h v c u r r e n t s a m p l i n g r e c t i f i e d m a i n s v o l t a g e v mainshigh v brownin figure 6. detecting mains connection by a positive dv/dt if a positive dv/dt is not detected for 28 ms, the system assumes that the mains is disconnected. in that case, the hv pin is continuously pulled to ground, discharging the external x-capacitor. 8.5 auxiliary winding to supply the control ic efficiently, the vcch and vccl pins are connected to auxiliary windings via a diode and a capacitor. to detect demagnetization and input and output voltage, one of the auxiliary windings is connected to the aux pin via a resistive divider (see figure 21 and figure 22 ). each switching cycle is divided in sections. during each section, the system knows if the voltage or current out of the aux pin reflects the demagnetization, valley, input voltage, or output voltage (see figure 7 ). aaa-020159 v i measurement demagnetization valley v o measurement v i 0 -0.7 v aux driver drain figure 7. aux pin used for demagnetization and input and output voltage measurement when the external mosfet is switched on, the voltage at the auxiliary windings reflects the input voltage. the aux pin is clamped to ?0.7 v. the output current is a measure of the input voltage. this current value is internally used to set the overpower limit on v sense(ipk) . the demagnetization, valley and output voltages are measured as a voltage on the aux pin. in this way, the input voltage measurement and ovp can be adjusted independently.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 10 / 34 8.6 protections if a protection is triggered, the controller stops switching. to avoid false triggering, some protections have a built-in delay. table 4. protections protection delay action v cc regulated aux open no wait until aux is connected no brownout 30 ms wait until v mains > v bi yes maximum on-time no safe restart yes otp internal 4.5 s safe restart yes otp via the protect pin 2 ms to 4 ms safe restart yes ovp via the aux pin 4 driver pulses [1] safe restart yes ovp via vccl pin 4 driver pulses [1] safe restart yes overpower timeout 40 ms to 200 ms safe restart yes overpower + uvlo no safe restart yes overcurrent protection blanking time cycle-by-cycle no uvlo no wait until v vccl > v startup yes [1] when the voltage on the protect pin is below v det(protect) , the clock of the delay counter is changed from the driver pulse to 1 ms internal pulse. when the system stops switching, the vcch and vccl pins are not supplied via the auxiliary winding anymore. depending on the protection triggered, v vccl is either regulated to the v startup level via the hv pin or dropped down until the uvlo protection triggered (see table 4 ). 8.6.1 overpower protection (opp) the overpower protection function is used to realize a maximum output power which is nearly constant over the full input mains. for applications intended to operate fully in dcm mode, a constant overpower protection level can be set by using the flat portion of the opp curve (see figure 8 ). on the other hand, applications designed to operate in qr mode at maximum power require the opp level to be compensated for mains. they can be set to use the variable part of the opp curve. the resistors connected to the aux pin set the i aux . they determine which part of the opp curve is used by the application. the overpower compensation circuit measures the input voltage via the aux pin. the circuit outputs an overpower reference voltage that depends on this input voltage. if the measured voltage at the isense pin exceeds the overpower reference voltage (v opp(isense) ), the driver output is pulled low (the primary stroke is cut short). the overpower timer starts. in this way, the system limits the power to the maximum rated value on a cycle-by-cycle base. if the overpower situation persists continuously for 200 ms, an overpower timeout is triggered. figure 8 shows the overpower protection curve.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 11 / 34 aaa-023506 (mv) 510 298 0.3 1.46 l aux (ma) v opp(isense) r e g i o n o p t i m i z e d f o r d c m o p e r a t i o n region op t i m i z e d for qr ope r a t i o n figure 8. overpower protection curve during system start-up, the maximum timeout period is lowered to 40 ms. when the output voltage is within its regulation level, the maximum timeout period returns to 200 ms, limiting the output power to a minimum at a shorted output. shortening the overpower timer ensures that the input power of the system is limited to < 5 w at a shorted output. if the load requires more power than allowed by the opp limit, the output voltage drops because of the limited output power. as a result, the v cc voltage also drops and uvlo can be triggered. to retain the same response in an overpower situation (whether uvlo is triggered or not), the system enters the overpower protection mode when overpower and uvlo are detected. the system entering the protection mode does not depend on the value of the op counter. 8.6.2 overvoltage protection (ovp; pins aux and vccl) an accurate output ovp is implemented by measuring the voltage at the aux pin during the secondary stroke. as the auxiliary winding voltage is a well-defined replica of the output voltage, the external resistor divider ratio r aux2 / (r aux1 + r aux2 ) can adjust the ovp level. an accurate ovp circuit is also connected to the vccl pin. it measures if the vccl pin voltage exceeds the level v ovp(vccl) at the end of primary stroke. an internal counter of four gate pulses prevents false ovp detection which can occur during esd or lightning events. 8.6.3 protection input (protect pin) the protect pin is a general-purpose input pin. it can be used to trigger one of the protection types shown in table 4 . when the voltage on the protect pin is pulled below v det(protect) (0.5 v), the converter is stopped. the protect pin can be used to create an otp function. to create the otp function, a negative temperature coefficient (ntc) resistor must be connected to this pin. when
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 12 / 34 the voltage on the protect pin drops to below 0.5 v, overtemperature is detected. the protect current (maximum 74 a) flowing through the external ntc resistor creates the voltage. the protect voltage is clamped to maximum 1.45 v. at room temperature, the resistance value of the ntc resistor is much higher than at high temperatures. because of the clamp, the current out of the protect pin is 1.45 v divided by the resistance, which is much lower than 74 a. a filter capacitor can be connected to the protect pin. to avoid false triggering, an internal filter of 2 ms to 4 ms is applied. 8.6.4 overtemperature protection (otp) if the junction temperature exceeds the thermal temperature shutdown limit, an integrated otp feature ensures that the ic stops switching. otp is a safe restart protection. a built-in hysteresis ensures that the internal temperature must drop 10 c degrees before the ic restarts. 8.6.5 maximum on-time the controller limits the on-time of the external mosfet to 55 s. when the on-time is longer, the ic stops switching and enters safe restart mode. 8.6.6 safe restart if a protection is triggered and the system enters the safe restart mode (see table 4 ), the system restarts after a delay time (t d(restart) ). an internal current source (i cc(dch) ) discharges the voltage on pin vccl. the discharge allows the conditions at a restart to be similar to a normal start-up. because the system is not switching, the vccl and vcch pins are supplied from the mains via the hv pin. after the restart delay time (t d(restart) ), the control ic measures the mains voltage. if the mains voltage exceeds the brownin level, the control ic activates the protect pin current source and the internal voltage sources connected to the ctrl pin. when the voltages on these pins reach a minimum level, the soft start capacitor on the isense pin is charged and the system starts switching again. the v cc is continuously regulated to the v startup level until the output voltage is within the regulation level again.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 13 / 34 8.7 optobias regulation (ctrl pin) in a typical application, the output voltage (or current) is sensed on the secondary side (by a tl431 or a controller such as tea190x). the feedback signal is passed to the primary side via an optocoupler. the optocoupler sends the current information to the ctrl pin of the TEA19363T . (see figure 21 and figure 22 ). the TEA19363T applies a relatively fixed voltage at the ctrl pin (the input impedance of the ctrl pin is r int(ctrl) ). it senses the current through the optocoupler. the TEA19363T compares the current with an internal regulation level i io(reg)ctrl (80 a). the difference is integrated with a slow time constant (in ms). it is added to the control signal that sets the output power. if the optocurrent (at ctrl pin) exceeds the regulation level (i io(reg)ctrl) ), the control signal reduces in this way, which leads to an output power decrease and vice versa. the optocurrent (at the ctrl pin) slowly regulates toward the regulation level (i io(reg)ctrl ). the result is a constant optocurrent during stable operation at all output power levels. aaa-021 135 ctrl a/d d/a offset 80 a 6 k ctrl_p figure 9. optobias regulation figure 9 shows the slow optocurrent regulation loop. in addition to the slow optocurrent regulation loop described above, the ctrl current directly contributes to the internal power control by creating a voltage drop across a 6 k resistor (see figure 9 ). it determines the transient behavior of the power regulation loop, which remains similar to ics, like the tea1836. the control loop responds to load or line variations through this direct optocurrent contribution, whereas the slow offset loop simply sets the steady state operation point. the advantages of this type of regulation are: ? the optocoupler collector parasitics do not influence the loop. so, more freedom in tuning the loop characteristics is ensured. ? unlike the traditional situation where the optocoupler current becomes much higher at lower output power, it retains the same low value in steady state at all powers. since the optocurrent is only 80 a even at low powers, a load step to a very high load can result in a maximum decrease of the optocurrent by this amount only. it limits the possible power increase. to counter this possibility, the offset loop enters a fast regulation mode when a significant optocurrent decrease is detected (to about 20 a
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 14 / 34 under the regulation level). the fast regulation mode ensures a quick output power increase. 8.8 burst mode operation when the output power drops to below the minimum level the system can supply while operating at the minimum power setting (i.e. the switching frequency is at its minimum), it can no longer reduce the optocurrent level to the regulation level i io(reg)ctrl (= 80 a). in this situation, the optocurrent increases to exceed the level of the burst threshold (i th(burst)ctrl ) and the burst mode is entered. switching is paused and a burst-off period commences. consequently, the optocurrent decreases. when it drops to below the i th(burst)ctrl , a new burst of switching cycles is started (see figure 10 and figure 11 ). figure 10 shows that all the operating frequencies are outside the audible area. the minimum switching frequency is f sw(min) and the burst mode repetition target period is t burst . the requested output power determines the number of pulses at each burst period. at higher output power, the number of switching pulses increases. at low load, it decreases. this burst mode regulation allows low-load operation without compromising on spectral purity, while keeping the output ripple limited. in addition, the optocoupler current is maintained at a very low level during low-load and standby operation. the result is a very low standby power consumption. to ensure good efficiency at very low load, the minimum number of switching cycles is set to 1. when the minimum number of pulses is reached, the burst repetition period cannot be reduced further. as the power decreases, the repetition rate of the single-pulse bursts decreases as well to a very low value. to improve further, the no-load input power and efficiency at low load, the current consumption of the ic is lowered to 240 a during the non-switching period in the burst mode. aaa-023815 t t burst f sw = f sw(min) p t burst f sw = f sw(min) > t burst f sw = f sw(min) figure 10. burst mode operation to achieve a good transient response at an increased output load, the system starts switching immediately when i ctrl drops to below i start(burst) . it keeps switching until the optocurrent exceeds the level of i start(burst)ctrl (100 a). however, to achieve a good transient response at a decreased output load, the system stops switching immediately when the optocurrent exceeds the level of i stop(burst)ctrl (200 a) at a decreased output load. in both situations, the calculated number of switching pulses by the internal digital circuit is overruled for the present burst cycle.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 15 / 34 aaa-023524 < t burst i load i ctrl driver i th(burst)ctrl i stop(burst)ctrl < t burst t burst > t burst > t burst figure 11. transient response in burst mode even though the burst-mode regulates toward a target repetition frequency, the actual repetition rate is lower than the target because of the discrete number of switching cycles. increasing or decreasing the number of pulses results in a step change in the burst repetition frequency. before reducing the number of pulses in the next burst, it is ensured that the resulting repetition rate does not exceed the target frequency. hence, at any moment in burst- mode operation, the actual burst repetition rate is within a band under the target frequency. if the number of burst pulses decreases, the effect of adding a pulse increases and the band becomes wider (see figure 12 ). n pulses 0 1 0 8 1 2 1 4 4 6 2 1 1 1 1 5 9 1 3 5 7 3 aaa-023816 1.8 0 burst repetition frequency (khz) (2) (1) 0.2 0.6 1 0.4 0.8 1.2 1.6 figure 12. upper and lower limits of burst frequency when the burst on time is 1.5 times longer than the target period (t burst ), the system switches to normal mode again. 8.9 soft start-up (isense pin) to prevent audible noise during start-up or a restart condition, an integrated soft start feature is implemented. when the converter starts switching, the primary peak current slowly increases to the regulated level with 15 steps. the soft start time constant is 3.7 ms, set by an internal time.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 16 / 34 8.10 driver (driver pin) the driver circuit to the gate of the power mosfet has a current sourcing capability of 300 ma and a current sink capability of 750 ma. these capabilities allow a fast turn-on and turn-off of the power mosfet for efficient operation. the maximum driver output is limited to 10.5 v. the driver output pin can be connected to the gate of a mosfet directly or via a resistor.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 17 / 34 9 limiting values table 5. limiting values in accordance with the absolute maximum rating system (iec 60134). symbol parameter conditions min max unit voltages v io(hv) input/output voltage on pin hv ?0.4 +700 v v vcch voltage on pin vcch dual supply voltage ?0.4 +120 v v vccl voltage on pin vccl dual supply voltage - 50 v v io(ctrl) input/output voltage on pin ctrl ?0.4 +12 v v i(isense) input voltage on pin isense ?0.4 +12 v v io(protect) input/output voltage on pin protect current limited ?0.4 +5 v v io(aux) input/output voltage on pin aux current limited ?5 +5 v currents i io(aux) input/output current on pin aux ?1.5 +1 ma i io(hv) input/output current on pin hv ?1 +5 ma i io(ctrl) input/output current on pin ctrl ?3 0 ma i io(protect) input/output current on pin protect ?1 +1 ma general p tot total power dissipation t amb < 75 c - 1 w t stg storage temperature ?55 +150 c t j junction temperature ?40 +150 c
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 18 / 34 symbol parameter conditions min max unit electrostatic discharge (esd) class 1 human body model [1] pins hv and vcch - 1000 v all other pins - 2000 v v esd electrostatic discharge voltage charged device model [2] - 500 v [1] according to jedec js-001. [2] according to jedec jesd22-c101 and ansi s5.3.1. 10 recommended operating conditions table 6. recommended operating conditions symbol parameter conditions min max unit voltages v io(hv) input/output voltage on pin hv 0 380 v v vcch voltage on pin vcch dual supply voltage 0 120 v v vccl voltage on pin vccl dual supply voltage; continuous - 45 v v io(ctrl) input/output voltage on pin ctrl 0 5 v v i(isense) input voltage on pin isense 0 5 v v io(protect) input/output voltage on pin protect current limited 0 2 v v io(aux) input/output voltage on pin aux current limited ?5 +5 v currents i io(aux) input/output current on pin aux ?1 +1 ma i io(hv) input/output current on pin hv 0 2 ma i io(ctrl) input/output current on pin ctrl ?1 0 ma i io(protect) input/output current on pin protect ?1 +1 ma general t j junction temperature ?25 +125 c
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 19 / 34 11 thermal characteristics table 7. thermal characteristics symbol parameter conditions typ unit r th(j-a) thermal resistance from junction to ambient jedec test board 148 k/w r th(j-c) thermal resistance from junction to case jedec test board 86 k/w 12 characteristics table 8. characteristics limits are production tested at 25 c and are guaranteed by statistical characterization in the temperature operating range. v cc = 20 v; all voltages are measured with respect to ground (pin 2); currents are positive when flowing into the ic; unless otherwise specified. symbol parameter conditions min typ max unit start-up current source (hv pin) v hv > 10 v 0.8 1.15 1.5 ma i startup(hv) start-up current on pin hv v cc > v startup ; hv not sampling - - 1 a v clamp clamp voltage i hv < 2 ma - - 680 v supply voltage management (vccl pin) v startup start-up voltage 13.4 14.9 16.4 v v intregd(vccl) internal regulated voltage on pin vccl via vcch; i cc = 0.5 ma 12.1 12.5 12.9 v v restart restart voltage burst mode 9.9 11 12.1 v v th(uvlo) undervoltage lockout threshold voltage 9.0 9.9 10.8 v v rst reset voltage 7.75 8.65 9.55 v v hv = 0 v - 40 - a i cc(startup) start-up supply current v hv > 10 v ?1.45 ?1.1 ?0.75 ma i cc(oper) operating supply current driver unloaded; excluding optocurrent - 600 - a i cc(burst) burst mode supply current non-switching; excluding optocurrent - 250 - a i cc(prot) protection supply current - 235 - a i cc(dch) discharge supply current safe restart protection; v cc > v startup 1.45 1.88 2.25 ma mains detect (hv pin) t p(hv) pulse duration on pin hv measuring mains voltage 18.5 20.6 22.7 s f meas(hv) measurement frequency on pin hv measuring mains voltage 0.89 1.0 1.11 khz
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 20 / 34 symbol parameter conditions min typ max unit t d(norm)hv normal mode delay time on pin hv measuring mains voltage 5.3 6.0 6.7 ms t d(burst)hv burst mode delay time on pin hv measuring mains voltage 87 97 107 ms i bo(hv) brownout current on pin hv 552 587 622 a i bi(hv) brownin current on pin hv 623 663 703 a i bo(hys)hv hysteresis of brownout current on pin hv - 76 - a i clamp(hv) clamp current on pin hv during measurement time - - 1.75 ma v meas(hv) measurement voltage on pin hv - 2.9 - v t d(dch) discharge delay time x-capacitor discharge; hv pin - 28 - ms t d(det)bo brownout detection delay time - 30 - ms peak current control (pin ctrl) v io(ctrl) input/output voltage on pin ctrl - 2.7 - v r int(ctrl) internal resistance on pin ctrl - 1.7 - k i io(startup)ctrl start-up input/output current on pin ctrl ?580 ?500 ?420 a burst mode (pin ctrl) i th(burst)ctrl burst mode threshold current on pin ctrl ?125 ?110 ?95 a i stop(burst)ctrl burst mode stop current on pin ctrl ?230 ?200 ?170 a t burst burst mode period - 600 - s oscillator f sw(max) maximum switching frequency 120 128 136 khz f sw(min) minimum switching frequency burst mode 2 pulses 23 25.5 28 khz current sense (pin isense) output overpower v opp(isense) mv v sense(peak) peak sense voltage burst mode 130 145 160 mv t pd(sense) sense propagation delay from the isense pin reaching v sense(max) to driver off; v isense pulse- stepping 100 mv around v sense(max) - 120 - ns
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 21 / 34 symbol parameter conditions min typ max unit t leb leading edge blanking time 275 325 375 ns soft start (pin isense) t start(soft) soft start time 3.3 3.7 4.1 ms demagnetization and valley control (pin aux) v det(demag) demagnetization detection voltage 20 40 60 mv i prot(aux) protection current on pin aux - ?200 - na t blank(det)demag demagnetization detection blanking time 1.9 2.3 2.7 s positive v/t 0.25 0.37 0.49 v/s (v/t) vrec valley recognition voltage change with time negative v/t ?2.45 ?1.95 ?1.5 v/s t d(vrec-swon) valley recognition to switch-on delay time - 120 - ns v clamp(aux) clamp voltage on pin aux i aux = 1 ma 4.4 4.8 5.2 v t sup(xfmr_ring) transformer ringing suppression time 2.0 2.4 2.8 s maximum on-time (pin driver) t on(max) maximum on-time 45 55 65 s driver (pin driver) i source(driver) source current on pin driver v driver = 2 v - ?0.3 - a v driver = 2 v - 0.3 - a i sink(driver) sink current on pin driver v driver = 10 v - 0.75 - a v o(driver)max maximum output voltage on pin driver 9 10.5 12 v overpower protection (pin isense and pin aux) v clamp(aux) clamp voltage on pin aux primary stroke; i aux = ?0.3 ma ?0.8 ?0.7 ?0.6 v t d(clamp)aux clamp delay time on pin aux after rising edge of pin driver 1.9 2.3 2.7 s counter trigger level i aux = ?0.3 ma 460 510 560 mv v opp(isense) overpower protection voltage on pin isense i aux = ?1.46 ma 268 298 328 mv start-up mode; i ctrl < 100 a 35.5 40 44.5 ms t d(opp) overpower protection delay time normal mode 178 200 222 ms t d(restart) restart delay time 890 1000 1110 ms external protection (pin protect)
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 22 / 34 symbol parameter conditions min typ max unit v det(protect) detection voltage on pin protect 0.47 0.5 0.53 v v det(hys)protect detection voltage hysteresis on pin protect - 50 - mv i o(protect) output current on pin protect normal mode ?79 ?74 ?69 a v clamp(protect) clamp voltage on pin protect 1.2 1.4 1.6 v overvoltage protection (pin aux) v ovp(aux) overvoltage protection voltage on pin aux 2.88 3 3.12 v v ovp(vccl) overvoltage protection voltage on pin vccl 46.5 48 49.5 v t det(ovp) overvoltage protection detection time in the secondary stroke 2 2.4 2.8 s temperature protection t pl(ic) ic protection level temperature 130 140 150 c t pl(ic)hys hysteresis of ic protection level temperature - 10 - c
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 23 / 34 12.1 typical temperature performance characteristics 12.1.1 start-up voltage aaa-023936 -40 -10 20 50 80 110 140 14 14.5 15 15.5 16 t (c) v startup v startup (v) (v) figure 13. start-up voltage as a function of temperature 12.1.2 undervoltage lockout threshold voltage aaa-023965 -40 -10 20 50 80 110 140 9 9.4 9.8 10.2 10.6 11 t (c) v th(uvlo) v th(uvlo) (v) (v) figure 14. undervoltage lockout threshold voltage as a function of temperature
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 24 / 34 12.1.3 detection voltage (pin protect) aaa-023969 -40 -10 20 50 80 110 140 480 490 500 510 520 t (c) v det(protect) v det(protect) (mv) (mv) figure 15. detection voltage (pin protect) as a function of temperature 12.1.4 switching frequency aaa-024157 -40 -10 20 50 80 110 140 100 110 120 130 140 150 t (c) f sw f sw (khz) (khz) figure 16. switching frequency as a function of temperature
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 25 / 34 12.1.5 overpower protection voltage (pin isense) aaa-023967 -40 -10 20 50 80 110 140 450 470 490 510 530 550 t (c) v opp(isense) v opp(isense) (mv) (mv) figure 17. overpower protection voltage (pin isense) as a function of temperature 12.1.6 overpower protection (at i aux = 1.46 ma) aaa-023968 -40 -10 20 50 80 110 140 260 270 280 290 300 310 320 t (c) v opp v opp (mv) (mv) figure 18. overpower protection voltage (at i aux = 1.46 ma) as a function of temperature
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 26 / 34 12.1.7 output current (pin protect) aaa-023970 -40 -10 20 50 80 110 140 -90 -80 -70 -60 -50 t (c) i o(protect) i o(protect) (a) (a) figure 19. output current (pin protect) as a function of temperature 12.1.8 overvoltage protection voltage (pin aux) aaa-023971 -40 -10 20 50 80 110 140 1 2 3 4 5 t (c) v ovp(aux) v ovp(aux) figure 20. overvoltage protection voltage (pin aux) as a function of temperature
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 27 / 34 13 application information aaa-020161 hv ic n.c. ctrl gnd protect driver isense aux vcch vccl d sec s1 r sense r driver r aux1 r hv d1 d2 ntc d vcch d vccl r aux2 c vcch c vccl c out v out figure 21. TEA19363T application diagram aaa-023817 hv tea19363 tea1903 n.c. ctrl gnd protect driver isense aux vcch vccl d sec s1 r sense r driver r aux1 r hv d1 d2 ntc d vcch d vccl r aux2 c vcch c vccl c out v out vcc vout opto sgnd isns sw disch cc1 cc2 d+ d- . %-))'
% *?
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 28 / 34 14 package outline references outline version european projection issue date iec jedec jeita sot1437-1 sot1437-1_po 15-02-09 15-03-06 dimensions note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. so10: plastic small outline package; 10 leads; body width 3.9 mm; body thickness 1.35 mm sot1437-1 unit m m max nom min 1.75 0.25 0.49 0.25 6.3 1.27 6.00 0.70 0.70 a a 1 a 2 1.45 a 3 b p c d (1) 8 e (1) 3.9 e h e l 1.05 l p q 6.20 1.00 4.0 v w 0.18 0.25 0.43 0.22 6.2 0.1 0.56 1.35 0.25 0.25 y z 0.10 0.36 0.19 6.1 0.30 1.25 5.80 0.65 0.70 0.60 0.40 3.8 0 4 pin 1 index z 6 5 1 0 b p (10x) (8x) w e d e a x 0 scale 5 mm y h e v a a a 3 q detail x a 1 a 2 l p l 1 c figure 23. package outline sot1437-1 (so10)
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 29 / 34 15 abbreviations table 9. abbreviations acronym description cc constant current cv constant voltage dcm discontinuous conduction mode emi electromagnetic interference esd electrostatic discharge fr frequency reduction mosfet metal-oxide-semiconductor field-effect transistor ocp overcurrent protection opp overpower protection otp overtemperature protection ovp overvoltage protection qr quasi-resonant smps switch-mode power supply soi silicon-on_insulator uvlo undervoltage lockout vco voltage controlled oscillator
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 30 / 34 16 revision history table 10. revision history document id release date data sheet status change notice supersedes TEA19363T v.1 20161020 product data sheet - -
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 31 / 34 17 legal information 17.1 data sheet status document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objective specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification. [1] please consult the most recently issued document before initiating or completing a design. [2] the term 'short data sheet' is explained in section "definitions". [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. the latest product status information is available on the internet at url http://www.nxp.com . 17.2 definitions draft the document is a draft version only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. short data sheet a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request via the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer, unless nxp semiconductors and customer have explicitly agreed otherwise in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 17.3 disclaimers limited warranty and liability information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use nxp semiconductors products are not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customers own risk. applications applications that are described herein for any of these products are for illustrative purposes only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customers sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customers applications and products planned, as well as for the planned application and use of customers third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customers applications or products, or the application or use by customers third party customer(s). customer is responsible for doing all necessary testing for the customers applications and products using nxp semiconductors products in order to avoid a default of the applications and the products or of the application or use by customers third party customer(s). nxp does not accept any liability in this respect. limiting values stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale nxp semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customers general terms and conditions with regard to the purchase of nxp semiconductors products by customer. no offer to sell or license nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 32 / 34 quick reference data the quick reference data is an extract of the product data given in the limiting values and characteristics sections of this document, and as such is not complete, exhaustive or legally binding. export control this document as well as the item(s) described herein may be subject to export control regulations. export might require a prior authorization from competent authorities. non-automotive qualified products unless this data sheet expressly states that this specific nxp semiconductors product is automotive qualified, the product is not suitable for automotive use. it is neither qualified nor tested in accordance with automotive testing or application requirements. nxp semiconductors accepts no liability for inclusion and/or use of non- automotive qualified products in automotive equipment or applications. in the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall use the product without nxp semiconductors warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the product for automotive applications beyond nxp semiconductors specifications such use shall be solely at customers own risk, and (c) customer fully indemnifies nxp semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond nxp semiconductors standard warranty and nxp semiconductors product specifications. translations a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 17.4 trademarks notice: all referenced brands, product names, service names and trademarks are the property of their respective owners. greenchip is a trademark of nxp semiconductors n.v.
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge TEA19363T all information provided in this document is subject to legal disclaimers. ? nxp semiconductors n.v. 2016. all rights reserved. product data sheet rev. 1 20 october 2016 33 / 34 tables tab. 1. ordering information . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... .3 tab. 2. marking codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ...3 tab. 3. pin description .. . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . . ... . ... . ...5 tab. 4. protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... .10 tab. 5. limiting values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... 17 tab. 6. recommended operating conditions . . . . ... . ... . ... 18 tab. 7. thermal characteristics . . . . . . . . . . . . . ... . ... . ... . ... . ... . .. 19 tab. 8. characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ..19 tab. 9. abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ...29 tab. 10. revision history .. . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ...30 figures fig. 1. TEA19363T block diagram . . . . . . . . ... . ... . ... . ... . ... . ... .4 fig. 2. TEA19363T pin configuration (so10) .. . . ... . ... . ... 5 fig. 3. start-up sequence .. . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... 7 fig. 4. modes of operation . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . . ... . ... 7 fig. 5. mains voltage measuring .. . . . . . . . . ... . ... . ... . ... . ... . ... . 8 fig. 6. detecting mains connection by a positive dv/dt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . .. 9 fig. 7. aux pin used for demagnetization and input and output voltage measurement . . . ... . ... . ... . ... . ...9 fig. 8. overpower protection curve .. . . . . . . ... . ... . ... . ... . ... . 11 fig. 9. optobias regulation . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . .. 13 fig. 10. burst mode operation . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... .14 fig. 11. transient response in burst mode ... . . ... . ... . ... . ..15 fig. 12. upper and lower limits of burst frequency .. . ... . 15 fig. 13. start-up voltage as a function of temperature ... 23 fig. 14. undervoltage lockout threshold voltage as a function of temperature . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . 23 fig. 15. detection voltage (pin protect) as a function of temperature . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . 24 fig. 16. switching frequency as a function of temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . . 24 fig. 17. overpower protection voltage (pin isense) as a function of temperature . . . . . . . . ... . ... . ... . ... . ... 25 fig. 18. overpower protection voltage (at iaux = 1.46 ma) as a function of temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . . 25 fig. 19. output current (pin protect) as a function of temperature .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ...26 fig. 20. overvoltage protection voltage (pin aux) as a function of temperature . . . . . . . . . . . . . ... . ... . ... . ... . ... 26 fig. 21. TEA19363T application diagram .. . . . ... . ... . ... . ... . 27 fig. 22. TEA19363T application diagram with tea190xt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ..27 fig. 23. package outline sot1437-1 (so10) . . . ... . ... . ... .28
nxp semiconductors TEA19363T greenchip smps primary side control ic with qr/dcm operation and x-capacitor discharge please be aware that important notices concerning this document and the product(s) described herein, have been included in section 'legal information'. ? nxp semiconductors n.v. 2016. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com date of release: 20 october 2016 document identifier: TEA19363T contents 1 general description . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . . ... . . 1 2 features and benefits . . . . . . . . . . . . . ... . ... . ... . . ... . ... . ... . ...2 2.1 general features . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . 2 2.2 green features . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ..2 2.3 protection features .. . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ...2 3 applications ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . . ... . ... . ... . ... . .2 4 ordering information . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ... 3 5 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ... .3 6 block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ... 4 7 pinning information . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ... . 5 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . .. 5 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . . 5 8 functional description . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ..6 8.1 supply management . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ...6 8.2 start-up and undervoltage lockout (uvlo) . . . ..6 8.3 modes of operation . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . ..7 8.4 mains voltage measuring . . . . . . . . . ... . ... . . ... . ... . ... . ... . .8 8.5 auxiliary winding . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . 9 8.6 protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . 10 8.6.1 overpower protection (opp) . . . ... . ... . ... . ... . ... . ... .10 8.6.2 overvoltage protection (ovp; pins aux and vccl) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . . 11 8.6.3 protection input (protect pin) . . . ... . ... . ... . ... . .. 11 8.6.4 overtemperature protection (otp) ... . . . ... . ... . ...12 8.6.5 maximum on-time . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . . ... . .. 12 8.6.6 safe restart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . . 12 8.7 optobias regulation (ctrl pin) . . . ... . ... . ... . ... . ... . 13 8.8 burst mode operation . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . 14 8.9 soft start-up (isense pin) . . . . . ... . ... . ... . ... . ... . . ... . .15 8.10 driver (driver pin) .. . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . .. 16 9 limiting values . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . . ... . ... . ... . ... . .. 17 10 recommended operating conditions ... . . . ... . ... . 18 11 thermal characteristics . . . . . . . . . . . . . ... . ... . ... . ... . ... . ...19 12 characteristics . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . . 19 12.1 typical temperature performance characteristics .. . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... . .. 23 12.1.1 start-up voltage .. . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... 23 12.1.2 undervoltage lockout threshold voltage .. . ... . ... .23 12.1.3 detection voltage (pin protect) . ... . ... . ... . ... . ..24 12.1.4 switching frequency . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ...24 12.1.5 overpower protection voltage (pin isense) .. . . 25 12.1.6 overpower protection (at iaux = 1.46 ma) . . . .. 25 12.1.7 output current (pin protect) . . . . ... . ... . ... . ... . ... 26 12.1.8 overvoltage protection voltage (pin aux) . . ... . . .26 13 application information . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... 27 14 package outline . . . . . . . . . . . . . . . . . . . . . . . ... . . ... . ... . ... . ... . ... . .28 15 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... 29 16 revision history .. . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . . ... . .. 30 17 legal information . . . . . . . . . . . . . . . . . . . . . . . ... . ... . ... . ... . ... . ... 31

▲Up To Search▲

Price & Availability of TEA19363T

	To Download TEA19363T Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .